INSTEON 2420M User Manual download pdf

Indoor/Outdoor

INSTEON Motion Sensor Model #2420M

1. INTRODUCTION

The INSTEON Motion Sensor is an indoor/outdoor motion sensor that will

turn INSTEON controlled lights On and Off in response to movement

around your home. The sensor also contains a photocell, allowing you to

configure the unit to only turn your lights on at night. Pair the Motion Sensor

up with INSTEON software for almost limitless automation possibilities.

In this package you will find the Motion Sensor, a 9V battery, a swivel

mount, and 2 screws.

INSERT BATTERY

Use a small Philips head screwdriver to remove screw from battery

compartment on back of unit and remove cover. Attach the included 9 volt

battery. Do not replace compartment cover until instructed to do so later in

this manual. Wait 5 minutes for the circuit to stabilize. Then, to confirm unit

is functioning, tap the set button a couple of times while watching the front

of the unit. Each time you tap the Set button, a red LED behind the sensor

lens will flash. Don’t worry if the LED flashes when you are not tapping the

set button as it is simply indicating that motion is being detected.

(Close-up

of battery

compartment)

ACCESS POINTS

Motion Sensor requires at least one INSTEON Access Point (#2443)

product installed in your home. To confirm the Motion Sensor is within RF

range of your Access Point, have a friend watch the LED on the side of

your Access Point while you tap the set button on the Sensor (while holding

it where you plan to install it). Access Point’s LED will flash a couple times

every time you tap the set button if it is within range.

MOUNTING (See Locating Tips for Help)

1. Use the two small screws (included) to secure the swivel mounting

bracket at your desired location.

2. Slide Motion Sensor onto the swivel mounting bracket (sliding the unit

to the right) until you hear a click.

3. Aim Motion Sensor towards the area in which you wish to detect motion

(detection area).

4. Test by walking through the area, linked responders should turn on

when motion is sensed, and off 1 minute after last motion sensed.

Motion Sensor

Battery

Swivel

Mount

2- 3x18

Screws

3. SETUP

7. SETUP MODES

(

tional

)

SET JUMPERS

Jumpers are small plastic

“boxes” that act as a

switch. When mounted on

2 pins, the switch is “on”.

When mounted on 1 pin

(or missing), the switch is

“off”.

Jumper 1 – Sensitivity

To reduce Sensor’s

detection range (by

approximately 33%),

carefully remove the left-

most jumper, jumper 1

(from the single pin it is

mounted on) using a pair

of needle-nose pliers and

re-mount it on both pins.

4. SETUP INSTEON DEVICE CONTROL

LINKING TO INSTEON RESPONDERS

1. Press & hold the Set button on Motion Sensor for 5 seconds (until red

LED behind sensor lens begins steady blinking, you now have 4

minutes to complete step 2)

2. Press & hold set button

for 5 seconds on the INSTEON responder (e.g.

SwitchLinc) you would like the Motion Sensor to control (an LED may

blink and the connected load/bulb may flash)

3. Motion Sensor’s LED will stop blinking (if not try step 2 again)

4. Test by tapping the Motion Sensor’s set button. Each tap should

alternatively turn the device you linked (e.g. SwitchLinc) on and off.

(Motion Sensor’s LED will flash each time Set button is tapped)

5. Repeat this procedure for up to 32 responders you wish the Motion

Sensor to control.

For Multi-button responders (e.g. KeypadLinc) tap the button you wish to

control before pressing & holding its set button.

6. ADJUST DETECTION ARE

AIMING & SENSITIVITY

1. Tap Motion Sensor’s set button until the linked responder(s) turn off

2. Within 10 seconds walk well out of detection area

3. Wait 20 seconds

4. Walk into and near your detection area. Your linked responders will

turn on (LED will flash upon initial motion, then once every 8 seconds

during motion)

a. If LED does not flash while you are moving within the

desired detection area, re-aim Sensor (usually means

pointing the Sensor “up”)

b. If LED flashes while you’re moving outside detection area

i. Aim Sensor to decrease range (usually means

aiming the Sensor “down”)

ii. If aiming sensor does not generate desired results

place jumper 1 on both pins (see section (Choose

Modes)

Tap the set button once, wait 10 seconds, and activate motion to

establish the new setting.

Jumper 2 – Disable LED

If you wish to disable the LED (will still operate during setup), mount

umper 2 on both pins. Tap the set button once, wait 10 seconds, and

activate motion to establish the new setting.

Jumper 3 – Night-Only Mode

If you wish to have the Sensor operate only when dark, mount jumper

3 on both pins. Tap the set button once, wait 10 seconds, and activate

motion to establish the new setting. Note: It takes 3.5 minutes to

detect the difference between day and night.

Jumper 4 – On-Only Mode

If you wish to disable the automatic countdown “Off”, mount jumper 4

on both pins and the Motion Sensor will only send “On” Tap the set

button once, wait 10 seconds, and activate motion to establish the

new setting.

Jumper 5 – Not Used

Set

Button

2. OPERATION

WHEN MOTION IS SENSED

1. When motion is sensed the Motion Sensor will send an “On”

command to up to 32 linked INSTEON responders and flash it’s LED

(unless it is daytime and unit is in night-only mode)

2. Sensor will begin a 1 minute countdown

3. Whenever motion is sensed during countdown, the countdown will be

reset to 1 minute to easily allow you to create “occupied” versus

unoccupied modes for your home.

4. When countdown expires the Sensor will send an “Off” command to

all linked responders (unless it is in on-only mode)

APPLICATIONS

1. Turn driveway or front step lights on when visitors approach

2. Have your fountain always on when you are around (and off when

you are away)

3. Save money by having HVAC and lighting automatically go into

energy savings mode when no one is around

5. MOUNT SENSOR

Jumper 1

Jumper 2

Jumper 3

Jumper 4

Jumper 5

(not used)

Set button

1 2

Summary of Contents

Page 1 - Model #2420M

Indoor/Outdoor INSTEON Motion Sensor Model #2420M1. INTRODUCTION The INSTEON Motion Sensor is an indoor/outdoor motion sensor that will

11. TROUBLESHOOTINGSymptom Resolution Sensor won’t link to responders Move a dual-band INSTEON device (e.g. Access Point) closer to

Comments to this Manuals

No comments

INSTEON 2420M User Manual

Browse online or download User Manual for Motion detectors INSTEON 2420M. INSTEON 2420M User's Manual

Summary of Contents

Comments to this Manuals