Page 1 of 19 2452-222/2452-422/2452-522 - Rev: 1/21/2014 7:50 AM DIN Rail Dimmer Owner’s Manual 2452-222 (US) 2452-422 (EU) 2452-522 (AUS/NZ)
Page 10 of 19 2452-222/2452-422/2452-522 - Rev: 1/21/2014 7:50 AM 1) Press and hold controller button until it beeps Controller LED will start
Page 11 of 19 2452-222/2452-422/2452-522 - Rev: 1/21/2014 7:50 AM 2) Press and hold DIN Rail set button until it beeps a second time DIN Rail LED
Page 12 of 19 2452-222/2452-422/2452-522 - Rev: 1/21/2014 7:50 AM Specifications General Product name DIN Rail Dimmer Brand/manufacturer INSTEON
Page 13 of 19 2452-222/2452-422/2452-522 - Rev: 1/21/2014 7:50 AM X10 transmitter Yes X10 receiver Yes X10 status response Supported X10 resume
Page 14 of 19 2452-222/2452-422/2452-522 - Rev: 1/21/2014 7:50 AM AUS/NZ Hardwired remote control Yes, either latching or momentary switches suppo
Page 15 of 19 2452-222/2452-422/2452-522 - Rev: 1/21/2014 7:50 AM Troubleshooting Problem Possible Cause Solution The LED on DIN Rail is not turni
Page 16 of 19 2452-222/2452-422/2452-522 - Rev: 1/21/2014 7:50 AM DIN Rail, it takes a long time for other INSTEON devices it is controlling to res
Page 17 of 19 2452-222/2452-422/2452-522 - Rev: 1/21/2014 7:50 AM Phase Bridge Detect Beacon/RF Range Test Dimmer module automatically bridges the
Page 18 of 19 2452-222/2452-422/2452-522 - Rev: 1/21/2014 7:50 AM Certification and Warranty Certification This product has been thoroughly tested
Page 19 of 19 2452-222/2452-422/2452-522 - Rev: 1/21/2014 7:50 AM liability with respect to this product. For repair or replacement during the warr
Page 2 of 19 2452-222/2452-422/2452-522 - Rev: 1/21/2014 7:50 AM About DIN Rail Dimmer ...
Page 3 of 19 2452-222/2452-422/2452-522 - Rev: 1/21/2014 7:50 AM About DIN Rail Dimmer Installation Preparation CAUTIONS AND WARNIN
Page 4 of 19 2452-222/2452-422/2452-522 - Rev: 1/21/2014 7:50 AM Identify Switch Type Before you install DIN Rail behind a switch, you must determi
Page 5 of 19 2452-222/2452-422/2452-522 - Rev: 1/21/2014 7:50 AM Switch Operation Mode By default, DIN Rail is programmed for a latching switch. If
Page 6 of 19 2452-222/2452-422/2452-522 - Rev: 1/21/2014 7:50 AM Local Control Operations DIN Rail’s switch operation mode affects how it responds
Page 7 of 19 2452-222/2452-422/2452-522 - Rev: 1/21/2014 7:50 AM 3) Press and hold set button until it beeps a third time LED will start blink
Page 8 of 19 2452-222/2452-422/2452-522 - Rev: 1/21/2014 7:50 AM 2) Press and hold set button until it beeps a second time LED will start blin
Page 9 of 19 2452-222/2452-422/2452-522 - Rev: 1/21/2014 7:50 AM Make DIN Rail a Responder Control DIN Rail from another INSTEON device: 1) Press
Comments to this Manuals