INSTEON 2842-222 Owner's Manual download pdf (Page 4)

2452-222/2452-422/2452-522 Rev. 11/6/2012 1:27 PM / See Owner’s Manual for Warranty Information.

Protected under U.S. and foreign patents (see www.insteon.com)

Sensor won’t control

linked responders

a) Make sure LED flashes to confirm it has power and is sensing motion

b) Sensor is in night-only mode (and it is “day”)

c) Move a dual-band INSTEON device (e.g., Access Point) closer to the Motion Sensor

d) Sensor is in its 1 minute countdown

LED flashing rapidly

after motion is

detected

Sensor did not receive an acknowledgement from one or more linked devices. If this occurs

repeatedly you may need to move a dual-band INSTEON device closer to the Sensor or you may

need to unlink a device which is no longer in use in your home. If the INSTEON responders are no

longer available, you may either use software or perform a factory reset to remove the unwanted links.

LED not flashing

upon motion

a) You may need to wait up to 8 seconds to see the flash

b) Battery may need to be replaced

Not sensing motion

a) Light detected and unit is in night-only mode

b) Motion Sensor aimed too low

c) Temperature too high, or low (sensor needs to be able to distinguish between what is being sensed

and its surroundings

d) See Placement Tips section

LED is double

flashing upon motion

Low battery warning—replace with fresh battery

Remove Motion Sensor as a Controller

1) Press and hold the set button on Motion Sensor for 5 seconds

Motion Sensor LED (behind sensor lens) will start blinking red

2) Press and hold the set button on Motion Sensor for 5 seconds

Motion Sensor LED will continue blinking red

3) Press and hold the responder set button until it beeps

Motion Sensor LED will stop blinking

4) Test by tapping the set button on Motion Sensor

Former responder will not respond

Factory Reset

Return Motion Sensor to Factory Settings

1) If possible, remove Motion Sensor as a controller of all responders before proceeding*

2) Remove battery

3) Wait 15 seconds

4) While pressing the set button, reattach the battery

After about 2 seconds the LED will turn on

5) Continue pressing the set button for 5 seconds and then release the set button.

The LED will turn off after about 2 seconds

* If you do not unlink, your responder will to continue to respond to Motion Sensor even after factory reset procedure is complete.

Owner’s Manual and Tech Support

For the most up-to-date Quick Start Guide visit http://www.insteon.com/support

Call: INSTEON Support Line at 866-243-8022

FCC and IC Warnings

This device complies with FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit

pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.

CAUTION - To reduce the risk of overheating and possible damage to other equipment do not install to control a receptacle, a motor-operated appliance, a fluorescent lighting fixture, or a

transformer-supplied appliance. Gradateurs commandant une lampe a filament de tungstene – afin de reduire le risqué de surchauffe et la possibilite d’endommagement a d’autres materiels, ne

pas installer pour commader une prise, un appareil a moteur, une lampe fluorescente ou un appareil alimente par un transformateur.

1 2 3 4

Quick Start Guide 1

Comments to this Manuals

No comments

INSTEON 2842-222 Owner's Manual Page 4

Comments to this Manuals