®INSTEON Dimmer Module 2457D2Owner’s Manual®INSTEON Dimmer Module 2457D2Owner’s Manual
10When not using a central controller like the INSTEON Hub, INSTEON devices can be congured and linked manually on a device-to-device basis. It is st
11Linking with a Single-Button Controller2Make sure the Dimmer Module is On and then press and hold the Dimmer Module’s set button until the device do
12ABLinking with a Multi-Button Controller2Make sure the Dimmer Module is On and then press and hold the Dimmer Module’s set button until the device
13Multi-Linking or Making a Scene23 4Adjust your scene members to their desired state: on, o, or brightness level if dimming.Lamp 1Lamp 3Lamp 2Applia
14Unlinking from a Single-Button Controller1On your INSTEON controller, press and hold the set button until the device beeps.2Press and hold the set b
15AB1On your INSTEON controller, tap the desired control button and then press and hold the set button until the device beeps.Unlinking from a Multi-B
16Multi-Unlinking or Removing a Scene23One at a time, press and hold the set button on each scene member until it double-beeps.Tap the set button on y
17Use the local programming to set local on-level, ramp rates and even perform a factory reset.Local ProgrammingUse local programming to set local on-
18About Local ProgrammingLocal Programming FeaturesLinking Mode Readies the module for linking to another INSTEON device. As linking is directional, t
19Local Programming Flow ChartUnlinking ModeRamp Rate SelectRamp Rate Cycle through four presetsMulti-Unlinking ModeSelectOn Level Uses the current b
ContentsGetting StartedINSTEON Dimmer Module 4Device Overview Buttons Installation Leave Your Lamp On INSTEON LinksUnderstanding Linking 6Links are
20Most INSTEON devices contain features that can only be enabled, disabled or modied using INSTEON control software such as HouseLinc and an INSTEON
21Software-Only FeaturesBeep on Button Press Disable Local ProgrammingBlink on Trac Error BlinkThe Dimmer Module will beep every time one of its butt
22Your INSTEON device features backwards compatibility with legacy X10 devices and can respond to X10 powerline messages.X10 SupportYour INSTEON devic
23Setting the X10 Address2Using an X10 controller, send the desired X10 address followed by the On command three times.1Press and hold the set button
24Removing the X10 Address1Press and hold the set button on your Dimmer Module until the device beeps.2Press and hold the set button again until the d
25Everything else you might need to know about your INSTEON product.AppendixEverything else you might need to know about your INSTEON product.Appendix
26INSTEON GlossaryController The INSTEON transmitterResponder The INSTEON receiverBlinking LED turning on and o repeatedlyDual-Band An INSTEON device
27SpecicationsGeneralAvailable Colors WhiteBrand: INSTEONFCC ID SBP2475D2AIndustry Canada 5202A-2475D2AManufacturer Product No.: 2475D2Patent No.: Pr
28Maximum Scene Memberships 400Multi-Link Support YesMulti-Unlink Support YesRF Beacon YesRadio Frequency 915.0 MHzRadio Frequency Range 150 feetScene
29ElectricalControlled Outlet Yes, ungrounded polarized. NEMA 1-15 typeHardwired Remote Control NoLoad Types Plug-in incandescent lighting sourcesMaxi
3Everything you need to quickly get up and running.Getting StartedEverything you need to quickly get up and running.Getting Started
30TroubleshootingDimmer Module LED does not turn onIt is possible your Dimmer Module is not receiving power. If the attached load can still be control
31TroubleshootingThe connected lamp turned on by itselfThere must be a device in your INSTEON network that is unexpectedly linked to the Dimmer Module
32Certications and WarningsRead and understand these instructions before installing and retain them for future reference.This product is not designed
33Product WarrantyLimited WarrantySeller warrants to the original consumer purchaser of this product that, for a period of two years from the date of
4Leave Your Lamp OnInstallationButtonsDevice OverviewINSTEON Dimmer ModuleSet ButtonOnOStatus LEDOnO®Plug your lamp into the bottom of the Dimmer M
5INSTEON devices can stand alone and function as a local switch or dimmer, but their real power comes when they are connected together to form a contr
6When linking INSTEON devices, the links that are created are one-way.The current state of the controlled device is stored in the link: on, o or dimm
7Controller-OnlySome devices like sensors can only control other devices.The Motion Sensor will turn on the Switch but the switch cannot control the M
8The INSTEON Hub allows you to congure your device, customize its properties, create scenes and more, all from your smartphone or tablet.INSTEON HubT
9You can now control your Dimmer Module from the INSTEON Hub.Linking to the INSTEON Hub14From Rooms, navigate to All Devices.When prompted, press and
Comments to this Manuals