®INSTEON On/Off Module 2635-222Owner’s Manual®INSTEON On/Off Module 2635-222Owner’s Manual
10ABLinking with a Multi-Button Controller2Make sure the On/Off Module is On and then press and hold the On/Off Module’s set button until the device d
11Multi-Linking or Making a Scene23 4Adjust your scene members to their desired state: on, off, or brightness level if dimming.Lamp 1Lamp 3Lamp 2Appli
12Unlinking from a Single-Button Controller1On your INSTEON controller, press and hold the set button until the device beeps.2Press and hold the set b
13AB1On your INSTEON controller, tap the desired control button and then press and hold the set button until the device beeps.Unlinking from a Multi-B
14Multi-Unlinking or Removing a Scene23One at a time, press and hold the set button on each scene member until it double-beeps.Tap the set button on y
15Use the local programming to set local on-level, ramp rates and even perform a factory reset.Local ProgrammingUse local programming to set local on-
16About Local ProgrammingLocal Programming FeaturesLinking Mode Readies the module for linking to another INSTEON module. As linking is directional, t
17Local Programming Flow Chart®Unlinking ModeMulti-Unlinking ModeSelectLinking ModeRF Beacon RF Beacon ToggleMulti-Linking Mode SelectLED Brightness
18Most INSTEON devices contain features that can only be enabled, disabled or modied using INSTEON control software such as HouseLinc and an INSTEON
19Software-Only FeaturesBeep on Button Press Disable Local ProgrammingBlink on Trafc Error BlinkThe On/Off Module will beep every time one of its but
ContentsGetting StartedINSTEON On/Off Module 4Device Overview Buttons Installation Leave Your Appliance On INSTEON LinksUnderstanding Linking 6Link
20Everything else you might need to know about your INSTEON product.AppendixEverything else you might need to know about your INSTEON product.Appendix
21INSTEON GlossaryController The INSTEON transmitterResponder The INSTEON receiverBlinking LED turning on and off repeatedlyDual-Band An INSTEON devic
22SpecicationsGeneralAvailable Colors WhiteBrand: INSTEONFCC ID SBP26352Industry Canada 5202A-26352Manufacturer Product No.: 2635-222Patent No.: Prot
23Maximum Scene Memberships 400Multi-Link Support Ye sMulti-Unlink Support Ye sRF Beacon Ye sRadio Frequency 915.0 MHzRadio Frequency Range 150 feetSc
24ElectricalControlled Outlet Yes, grounded. NEMA 5-15 typeHardwired Remote Control NoLoad Types General Appliances 15A MaxResistive 15A MaxIncandesce
25TroubleshootingOn/Off Module LED does not turn onIt is possible your On/Off Module is not receiving power. If the attached load can still be control
26TroubleshootingThe connected appliance turned on by itselfThere must be a device in your INSTEON network that is unexpectedly linked to the On/Off M
27Certications and WarningsRead and understand these instructions before installing and retain them for future reference.This product is not designed
28Product WarrantyLimited WarrantySeller warrants to the original consumer purchaser of this product that, for a period of two years from the date of
3Everything you need to quickly get up and running.Getting StartedEverything you need to quickly get up and running.Getting Started
4Leave Your Appliance OnInstallationButtonsDevice OverviewINSTEON On/Off ModuleSet ButtonOnOffStatus LEDOnOff®Plug your appliance into the bottom of t
5INSTEON devices can stand alone and function as a local switch or dimmer, but their real power comes when they are connected together to form a contr
6When linking INSTEON devices, the links that are created are one-way.The current state of the controlled device is stored in the link: on, off or dim
7Controller-OnlySome devices like sensors can only control other devices.The Motion Sensor will turn on the Switch but the switch cannot control the M
8Linking to the INSTEON Hub14From Rooms, navigate to All Devices.When prompted, press and hold the set button on your On/Off Module until the device d
9Linking with a Single-Button Controller2Make sure the On/Off Module is On and then press and hold the On/Off Module’s set button until the device dou
Comments to this Manuals