
Page 1 of 21 2444-222/2444-422/2444-522 - Rev: 2/24/2014 9:10 AM Micro Open/Close Owner’s Manual 2444-222 (US) 2444-422 (EU) 2444
Page 10 of 21 2444-222/2444-422/2444-522 - Rev: 2/24/2014 9:10 AM Dual Momentary Wall Switch Adjust Local Settings Change LED Br
Page 11 of 21 2444-222/2444-422/2444-522 - Rev: 2/24/2014 9:10 AM This setting is only adjustable via software or a central contro
Page 12 of 21 2444-222/2444-422/2444-522 - Rev: 2/24/2014 9:10 AM Micro module will double-beep Controller will double-beep and i
Page 13 of 21 2444-222/2444-422/2444-522 - Rev: 2/24/2014 9:10 AM Scenes Devices in a scene can each have different settings. This
Page 14 of 21 2444-222/2444-422/2444-522 - Rev: 2/24/2014 9:10 AM LED will start blinking red 3) Press and hold Micro module Set
Page 15 of 21 2444-222/2444-422/2444-522 - Rev: 2/24/2014 9:10 AM 3) Send the X10 address 3 times (with or without commands) Exam
Page 16 of 21 2444-222/2444-422/2444-522 - Rev: 2/24/2014 9:10 AM Phase detect beacon Yes X10 Support Yes X10 Addresses Any 1 of 2
Page 17 of 21 2444-222/2444-422/2444-522 - Rev: 2/24/2014 9:10 AM Low voltage halogen Motor Hardwired remote control Yes, latching
Page 18 of 21 2444-222/2444-422/2444-522 - Rev: 2/24/2014 9:10 AM Troubleshooting Problem Possible Cause Solution The LEDs on Mic
Page 19 of 21 2444-222/2444-422/2444-522 - Rev: 2/24/2014 9:10 AM Micro module still controls devices even after factory reset The
Page 2 of 21 2444-222/2444-422/2444-522 - Rev: 2/24/2014 9:10 AM About Micro Open/Close ...
Page 20 of 21 2444-222/2444-422/2444-522 - Rev: 2/24/2014 9:10 AM Certification and Warranty Certification This product has been thoroughly
Page 21 of 30 prepaid, with proof of the date of purchase and an explanation of the defect or error. The repair, replacement, or refund that is p
Page 3 of 21 2444-222/2444-422/2444-522 - Rev: 2/24/2014 9:10 AM Limitations...
Page 4 of 21 2444-222/2444-422/2444-522 - Rev: 2/24/2014 9:10 AM About Micro Open/Close Features and Benefits - Two integrated
Page 5 of 21 2444-222/2444-422/2444-522 - Rev: 2/24/2014 9:10 AM DIMMING AN INDUCTIVE LOAD. Identifying the Electrical Wires in Y
Page 6 of 21 2444-222/2444-422/2444-522 - Rev: 2/24/2014 9:10 AM Installation 1) Write down the INSTEON ID found on the back of
Page 7 of 21 2444-222/2444-422/2444-522 - Rev: 2/24/2014 9:10 AM Switch Operation Mode By default, Micro module is programmed for
Page 8 of 21 2444-222/2444-422/2444-522 - Rev: 2/24/2014 9:10 AM Calibrate Micro Module Once wired in, you need to calibrate Micro
Page 9 of 21 2444-222/2444-422/2444-522 - Rev: 2/24/2014 9:10 AM Reverse Motor Direction For some applications, such as a projecto
Comments to this Manuals